The correct position of the mount is very important for the Ring Doorbell’s optimal working. You must be assured about where to position your ring doorbell.
Although, the correct position of a particular doorbell also depends on the doorbell version. Knowing some things about your model will decide the correct placement of it in your house.
If you want to install a new Ring doorbell at your home, you will require a manual for formal installation. We have provided some of the most crucial steps you will require to take to set up your doorbell properly.
Where To Position Ring Doorbell For Better Function ?
Quick Navigation
As you may have heard or known that the Ring doorbell is generally mounted above one’s eye level. To say this fact precisely, it is instructed that the ring doorbell should be almost 48 inches up from the floor.
It should be placed on your porch. While mounting, the doorbell should be placed flat against your wall or a door.
Several Kits can also adjust the Ring Doorbell at any angle you want. We will know about them further in the following article.
Some of the crucial characteristics that will confirm that your doorbell functions in good condition are given below:
1. To be fixed near about 48 inches off the ground
The optimal elevation at which the doorbell should be fixed is about 4 feet off the ground, which is forty-eight inches off the ground.
You will have to position the doorbell at this elevation. You can decide to mount it anywhere. It could be an outer wall or a door frame of your house.
The length mentioned is essential to enable the motion sensors to perceive the person near the entrance. They should not detect the activities that occur far from the door.
If positioned correctly, the movement sensors can also sense movement from 1.5 meters far and maintain a straight breadth of about 160 degrees.
Also it also helps your doorbell camera to have a considerably more vertical range of area under view. This will also enable you to see the faces of the individuals approaching your door.
2. It should be fixed flat and steady against your wall or a door.
Determining the perfect angle is a requirement for a clear view. It is also essential for the adequate working of the sensors.
However, many installation kits can also assist you in installation. Sometimes you just need the right angle or modify the angle, which affects the better functioning of your Doorbell.
Follow the given below steps if you are confused about the installation of your Ring doorbell:
- You should position the angle mount where you want your ring doorbell to go. You should examine the level with the given level tool.
- Utilizing the given drill bit or screwdriver, tighten the shorter two screws. Ensure it is tight enough to stay in the mount’s bottom and top holes.
- Use the anchors if you plan to install them in brick, stucco walls, or concrete. You have to place them in the screw holes. ( Remember that anchors are not required for installing the amount on wood.)
- You can expand the doorbell’s angle by eliminating the screws. You can also place an additional amount on top of the first and tighten the mounts.
- Now you have to Connect your Ring doorbell to the angle mount(s). If you want to try both a wedge mount and a corner mount, install the corner mount, always first. Then you can install the doorbell.
- Still, you can use the extra kits to adjust your Ring Doorbell horizontally or vertically.
3. It should be near the power source for the Ring doorbell
It is better than the Ring Doorbell should be hard-wired to the house’s existing cables the doorbell. This lowers your chances of placing your doorbell adequately.
Hence, this is why you must go for Ring Doorbell 2 or even a battery-operated Doorbell. Buying any of these doorbells provides you the convenience to set it up anywhere.
Either you want to introduce it right side from the frames of doors’ or the external walls. There is a need to think about the Ring doorbell’s power.
This is because it is also a factor in deciding the kind of doorbell you need. Also where you can position the same for optimal working.
Categories of Installation Kits
Ring provides two different categories of installation kits that can alter the angle of the Ring Doorbell. These kits are very helpful if you possess hard-wired doorbells.
It is easy to place a hard-wired doorbell. The exact angle is a requirement. This is because it helps in preventing motion detectors from sensing unwanted objects
These kits are
1. The Wedge kit: The Wedge Kit offers you the means to angle the Ring doorbell up or down from 5 to 15 degrees.
2. The Corner kit: The Corner Kit enables you to modify the horizontal angle of your Ring doorbell from 20 to 55 degrees.
Some Limitations about installation of the Ring Doorbell
- There are some limitations to the installation of your Ring doorbell. the primary of them is that the doorbells can’t be set up horizontally.
- Also, they don’t have screen rotation characteristics.
- Therefore, If you cannot place the video doorbell correctly, you will face the issue of sensors not working correctly.
- Also, you should see that the motion detector doesn’t function properly. Also, observe if the videos of the area are visible sideways.
- Each of these things creates it particularly hard for the customers to see who has neared the door. Furthermore, the motion sensors might work with some additional issues. So, you will need to find the perfect position to mount the video doorbell on its excellent working.
Final Talk
This article saw various vital factors we must consider while installing the Ring doorbell. We have covered every detail which is vital regarding the positioning of your Ring doorbell.
The company provides additional kits, which we talked about. You should make use of them. These kits will help you perfectly place the Ring doorbell in different positions.
We hope you were able to find the required clues from our article for installing your Ring doorbell.
Leave a Reply