How To Unlock A Deadbolt Door Without A Key?

Step 1: To begin, take out the power with a proper drill bit. Make sure the power drill bit is well fitted.
Step 2: Once finished, lubricate the drill bit. This will keep the drill bit from breaking from too much friction.
Step 3: After you’ve finished lubricating the drill bit, add a generous amount of oil around the deadbolt and within its keyhole.
Step 4: Place the drill bit’s tip in the middle of the keyhole, then squeeze the trigger on the power drill.
Step 5: You must apply pressure to the drill to drive the drill bit into the keyhole.
Step 6: Apply a lubricant to the keyhole once the drill bit has penetrated it to prevent the drill bit from breaking. Repeat this method until the back of the lock is successfully broken and the tumbler pins come out.
Step 7: Once you are done with drilling the deadbolt, insert the screwdriver and reach out to the locking system. Turn it like you are unlocking a door usually with a key.
Step 8: After successfully unlocking the door, you may remove the screwdriver.

Step 1: Before diving into the procedure, first check the model of the deadbolt lock and surround yourself with the required tools
Step 2: Keep in mind that to open any lock, the whole process is to repeat the unlocking action of the key.
Step 3: Now, start straightening your bobby pin. Then, put the rough end of the bobby pin into the deadbolt lock’s keyhole.
Step 4: Insert the tip of your tiny flat head screwdriver into the keyhole, right behind the bobby pin. Do not insert the screwdriver head too profoundly since you will need adequate space to move the bobby pin in numerous directions and in and out of the keyhole.
Step 5: Move the bobby pin to either side of the keyhole of the lock. You should be able to manipulate the tumbler pins inside the lock by doing so. While sliding the pins, slide the edge of your screwdriver between the pins.
Step 6: Make sure the screwdriver tip is long enough to hold all of the tumblers in place.
Step 7: Twist the screwdriver with all the tumblers within the lock-up to unlock the deadbolt. If you follow all of these instructions, you should succeed on your first try. If the initial attempt fails, experiment with alternative angles and move the bobby pin combinations.

Step 1: Slide the credit card’s margin between the door and the strike plate at a specified angle.
Step 2: Keep it straight and perpendicular to the door when inserting the card’s corner. The whole edge of the card will now be sandwiched between the door and the strike plate.
Step 3: Bend the credit card and press it with force. The bending will assist the credit card placed between the door and the strike plate.
Step 4: Insert the card inside the door and hit the plate by moving it up and down.
Step 5: While bending the card, press and shake the card between the door and the lock plate.
Step 6: Continue pushing the door and wiggling the card until it moves far enough to squeeze the latch. The door will be successfully opened when the card compresses the latch.

Step 1: If your door has a complicated lock, you can unlock it by completely bypassing it. Find enough space between door and door jam, so that you can pass a knife blade between them.
If there is enough space between the door jam and the door, a thin knife blade can be slipped between them.
Step 2: Once there, move the Knife up and down the striker plate until you reach the deadbolt.
Step 3: Push the Knife against the bolt to encourage it to go around it.
Step 4: Remove the bolt from its unlocked position.

Step 1: Fold the bottom of a conventional bobby pin for about 2cm to get an L-shaped bobby pin.
Step 2: To make sure the bobby pins fit perfectly into the deadbolt lock, take out any rubber balls if you find any at the other end.
Step 3: The other bobby pin can be taken out entirely and remove any rubber balls at the end. This will make an essential locking tool, which you will use to raise the pins within the lock.
Step 4: At the bottom of the keyhole insert the L-shaped bobby pin. Apply some sideways pressure to the L-shaped bobby pin
Step 5: This should cause the pins to be set and the deadbolt to unlock.