How To Replace Window Alarm Sensor?

You all must have installed a Windows security system. If not then get your hands on a window security system as soon as possible. The one thing that we cannot afford is the weak security in our houses. That is why we keep on replacing or fixing any loopholes in our security system. In this article, we will be learning about ways through which we can replace window alarm sensors. As soon as possible with the minimum materials required.

Methods To Change Window Alarm Sensor

Description

Further in the article, we will be learning about ways through which one can change. Reinstall or replace our window alarm sensor.

Tools

Double-sided tape, screwdriver, sensor

Time

It will take about 15-20 minutes. If you have all the required materials.

Total Time: 18 minutes

1. Remove The Old Sensor

To put a new sensor, you need to remove the old one. This can be done by removing them with the help of a screwdriver. you need to disable it, before removing it. If your old sensor is attached with the help of screws then a screwdriver will be enough.

If your sensor is attached with double-sided tape gently remove it from the tape. Further, if you want to reinstall then you can remove the remaining tape from the wall as well.

Your wired sensor might be a little difficult to remove. You need to pull it strongly. Make sure you do not take out the wires as they might help in reinstallation.

2. Connect The Wires Of Your New

Carefully, attach the new sensor to your window. Make sure it is properly wired. If you need some help, you can take the help of your manual. If your new sensor can be placed by double-sided tape, make sure you use it while placing it.

3. Mount Your New Sensor

Mount the new sensor properly. If the sensor is comfortable with the old magnet then there is no problem. But if it is not then you might need a new one. Surface-mounted sensors are placed with screws and double-sided tape.

A recessed sensor may need a new installation of a hole in your window. If your previous sensor was a recessed one then you can check the hole with the new one. If it fits then you can go with it. If it doesn’t then sadly you have to make some changes with your new one.

4. Check Alignment Of New Sensor

Check if the sensor is properly placed and aligned. Make sure there is no hindrance between the sensor and the window. After checking all the possible difficulties jump up to the next step.

5. Test Your New Setup

The last part is to test the sensor. Check the sensor by arming your security system. Put the security code on your keypad. If it is working properly, your system is armed. If it is not, then it will show some trouble on the keypad. If the trouble occurs, try to reattach it. Try to check the distance between the sensor and the window. Check if there is some hindrance.

6. If The System Is Not Responding, It Is Possible That Your Sensor Is Misaligned Or Too Far

As mentioned above, make sure that your system is properly attached. If the system is not responding check your sensor. Attach it properly, look for misaligned spaces in between the sensor and the window.

7. Either Troubleshoot Or Provide You With A Replacement Sensor

Correct the mistakes after finding them. Cover the loopholes, tighten the sensor. Make sure nothing is broken here. If you think that the issues cannot be fixed or the sensor is not correct. Then you can replace it with another one.

8. Finally Restore

Restore the sensor properly. After looking for all the loopholes. Finally, the work is done.

Tools:

Double-Sided tape
Screwdriver
Sensor

Materials: NA

FAQ

1. How Long Do Window Alarm Sensors Last?

A window alarming system usually lasts 5-7 years. A wireless alarm sensor takes almost 5 years for its batteries to wear out. But don’t worry, this will not affect your life in any case.
Most sensors are designed in a way in which the keypad will send a message when the batteries are about to die. This makes your life even easier as now you just need to charge your batteries and you are good to go.

2. How Do You Fit An Alarm Sensor?

It is very easy to fit any alarm sensor. As mentioned above, alarm sensors just need a couple of steps to be followed and you are good to go. You might need to read this entire article to fit an alarm sensor.
The earlier mentioned steps are the connection of wire. Mounting the wires and many more. You just need to make sure that all these steps are done with proper care and management.

3. Why Do I Need To Replace My Window Alarm Sensor?

You might need to replace your window alarm system due to several reasons. These could be as follows:

a. The sensor needs a replacement.
b. Replacement of batteries.
c. Sensor gets disrupted.
d. Outdated technology

All of these factors are secondary. The primary factor to replace your sensor would be security. We cannot compromise on security for all the obvious reasons. That is the reason we should keep replacing our security systems in 5-6 years. Also due to old technology, the system of the sensor weakens.

4. How Do You Replace A PIR Light Sensor?

To replace a PIR light sensor a person needs to follow a couple of steps. Remove the PIR lid. You can do it by unscrewing it from the bottom. Remove the lens present in the sensor. Do this process carefully. Now, the circuit board is visible.
Remove the wires, do not touch any wire. The red and the black wires are dangerous and we request you to not work with them. This can blow the fuse. Unscrew the plate of the PIR sensor and you are good to go.

5. How Do I Remove My ADT Sensor?

To remove the ADT sensor from windows or doors, you need to follow a couple of steps. The first step is to eliminate the double-sided tape and silicone glue. You must have put it while installing the ADT sensor. Take the help of a knife or a cutter to take that silicone glue out. You can choose the best ADT sensor for your doors and windows.
This step might be a little difficult to do. If you are finding it difficult to do, then you must buy a silicon glue remover to do the task. Please do not hurt yourself by pushing the silicon glue out. This might be harmful.

Final Talk

At last, we would like to recall that sensors are easy to put but a little difficult to replace. Make sure you are using all the protection while replacing it. Do not hurt yourself while handling the wires. Disable it before Following all the steps properly. Make sure you follow all the steps. read this article. We hope that this article would help you to do your replacing with a DIY method. You can also install a childproof window lock to maximize your child’s safety while avoiding intruders.