How To Drill Out A Lock Cylinder?

It is very easy to drill out a lock cylinder by twist bit or spur bit. Here we have tested some steps and enlisted the procedure to make your life easier. You can drill it out without using keys or by using screwdrivers. 

Steps To Drill Out A Lock Cylinder

Before going further, you need to examine the lock. A hardened steel centre pin is used in certain tubular locks to prevent drilling. Whereas a ball bearing is used in others to prevent drilling. Consult a local hardware store or locksmith if you’re not sure if the lock has a hardened centre pin.

Tools:

• A power drill with various speeds
• Well-maintained and powerful power drill
• Drill bits of various diameters are available

Materials: NA

Methods For Ignition Lock Cylinder:

The removal of an ignition-lock cylinder necessitates the use of a key. If you’re in a hurry, you can drill the lock open, but only as a last resort. You can damage the ignition switch and the lock cylinder.

Things you need: A drill bit

Time: 30-40 mins

Step 1: Test The Lock Cylinder

Test the lock cylinder with a drill bit to determine if it fits. A bit that is only a smidgeon smaller than the cylinder is required. Because drilling metal can harm standard drill bits.

Step 2: Secure

Secure the drill bit in place by tightening the drill chuck.

Step 3: Use Of A Low-Speed Drill

In step three, drill a beginning groove into the lock cylinder. Make a narrow cut at the end of the lock cylinder with a low-speed drill. You only need to drill a shallow hole to prevent the drill bit from slipping at greater speeds.

Step 4: Increase The Speed

Drill the lock cylinder by increasing speed to high. By this, drilling will help control the heavy lifting. Don’t oppress the drill into the lock cylinder. If you do so, then the risk of damaging the rotor within the drill motor is increased.

Methods For Chevy Lock Cylinder:

Here are the steps to drill out a chevy lock.

Things you need: Driller

Time: approx: 30-35 mins

Step 1: Drilling

Drill a hole in the lock cylinder to see if it works. A bit that is smaller than the cylinder is required. Because conventional drill bits can be damaged by drilling metal. To cut the cylinder you will require a hardened drill.

Step 2: Tighten

Tighten the drill chuck after locking the drill bit in place.

Step 3: Increase Speed

Using a drill, make a groove in the lock cylinder. For that use a low-speed drill. Drill the hole just enough to keep the drill bit from slipping at higher speeds.  If you want to drill out the lock cylinder, then the drill speed should be the highest.

Methods For Ford Lock Cylinder:

Things you need:

1. Acetylene gas torch
2. WD-40
3. Ice pick/Small drill
4. Centre punch
5. Needle nose pliers
6. Hammering block with anvil
7. Dead blow hammer
8. Metal file set

Step 1: Drill A Hole

Drill a hole in the lock cylinder using a centre punch and hammer. Then take it out of the housing using a pry.

Step 2: Locate A Starting Point

Pick a start point through which you can draw apart what remains of the piston sticking out from inside. While doing this be careful of the metal fillings geting mixed together.

Step 3: Drill Bit

Drill a hole in each corner of the Ford ignition cylinder casing with a drill bit.

Step 4: WD-40

Work WD-40 into any remaining spaces inside and on top of any drilled holes to release the grip. This will make it easier for removal with needle-nose pliers or an ice pick bit (if necessary).

Step 5: Use Of Ice pick

Insert an ice pick bit into each of the four corners of a shell.

Step 6: See The Inside

Pry out one of these corner holes with needle-nose pliers so that you can see what’s inside. Make sure the ice pick is tilted slightly upwards so it reaches its target point.

Step 7: Final Step

Clean all components before reinstalling them in the engine bay. You can test it by starting the car and opening/closing door locks. After everything has been reassembled.

Don’t omit any steps because there’s nothing more inconvenient than having to repeat them afterwards.

How To Take Out an Ignition Lock Cylinder Without a Key?

An important part of any vehicle will be an ignition lock cylinder. Despite how crucial it is, most car owners do not give it much thought.

They take it for granted until it breaks down and you can no longer use it or start your vehicle. Then you will have to replace it.

Removing the key is a straightforward operation if you have it. Without it, the procedure necessitates several more steps.

Things you need:

• Drill bit for a power drill
• Screwdriver with a flathead

Time: 40-50 mins

Step 1: Disconnecting The Battery 

Disconnecting the battery is the first step. This is a precaution to avoid shorting anything in your automobile. Or receiving an electric shock. To do so, you must first disconnect the negative cable connector.

Step 2: Remove The Steering Wheel

Remove all the screws attaching the steering wheel, and then push it upwards. And pull at the middle cover once the coverings have been removed. The wiring to the car horn can now be disconnected.

Step 3: Remove Wipers And Indicator Switches 

These are simple to locate using your car’s owner manual. And only need to be pushed away from their original location.

Step 4: Remove Steering Column Sleeve

The spacer columns should be located within the car’s steering wheel column. Slide them up once you’ve located them.

Step 5: Disconnecting The Electrics From The Ignition Switch

Locate the ignition switch’s mounting screws. And remove them before pulling the switch out. All of the wires should be disconnected from the appropriate connector. Loosen the tabs and then pull out the switch.

Step 6: Remove The Mounting Bolts

Detach the mounting bolts from the ignition switch with the help of a screwdriver. Then separate the housing and switch assembly that holds the lock cylinder completely.

Most car models come with universal lock cylinders that can be swapped out. You can remove these by inserting a pin through the pinhole and releasing the release mechanism.

Step 7: Examine Mounting Bolts for the Ignition Switch Housing

Some car models have safety bolt heads that are simple to remove. This part was created to keep thieves from stealing. Allowing them to drive without a key. A power drill will be required to remove the ignition switch from the steering wheel column.

Step 8: Locking The Key Cylinder

Turn the Ignition lock cylinder anti-clockwise using a straightened paper clip. This prevents the ignition from starting by locking the cylinder.

Step 9: Screwdriver

Place your screwdriver in the ignition lock’s cylinder. In a clockwise direction, turn as far as you can. Then, as far as you can, pull the paperclip to the right and slide the switch out.

How To Break Ignition Lock with Screwdriver?

The screws that hold the plastic trim in place should be located and removed. Then remove the plastic trim and get a hold of the ignition switch. Remove the bolt mounting on the steering wheels to unlock them. Turn right with the screwdriver in the keyhole.

You may remove the ignition lock cylinder without a key and start your automobile. by following these simple instructions When you need your car in an emergency and don’t have the money to hire a locksmith. Breaking the ignition lock with a screwdriver comes in handy.

Things you need:

1. Flathead screwdriver
2. Screwdriver

A flathead screwdriver’s size might vary. It could be small enough to alter the size of spectacles for usage in the workplace.

Step 1: Locate And Loosen The Screws 

The first step is to identify the screws that secure the plastic trim. Your car’s steering column is where you’ll find them.

You can now unscrew these screws with the flathead screwdriver. Once you’ve located them. Keep the screws in a safe place since you’ll need them to install the ignition lock.

Step 2: To Gain Access To The Ignition Switch

Remove the plastic trim and the bolts. After you’ve successfully removed the screws.  You can simply lift the pieces of plastic trim to remove them.

You’ll be able to see the ignition switch once you’ve removed all of the pieces. Free the steering wheel by removing the nuts and connecting the ignition.

Step 3: Removing The Screws

Remove the screws that connect the electrical and mechanical portions of the ignition switch. After that, put the screwdriver into the keyhole.

Step 4: Start The Vehicle

Now remove the screws that hold the electrical and mechanical portions of your ignition switch together. The component with the wires is the electrical part.

Once you’ve done that, you may now insert the screwdriver into the keyhole. This will now start your vehicle.

Final Talk

Once you learn how to drill out the ignition lock cylinder in the right way you will be confident enough for execution. Luckily, we have offered different and most effective ways to deal with the task and remove the ignition lock cylinder.