How To Change Emergency Light Bulbs?

At night emergency lights are the safest options to avoid accidents. If your emergency light is not working, you may have to replace them. We have covered a simple guide and step-by-step instructions to change the light bulbs. It can make your life easier in just a few steps.

Steps To Change Bulbs

Some of the reasons why one should change all lights with emergency bulbs are as follows:

1. The Light is loosely connected or Improperly fitted: If the bulb is loosely connected or improperly fitted, it causes voltage issues. This causes the intermittent voltage to flow through it. And due to this voltage, Flickering happens. Ultimately it leads to Burnout. One should ensure that the bulb is correctly screwed into its respective socket. If it is too tightly screwed, it will cause damage to the socket.

2. Loosely Screwed: If it is too loosely screwed, then screw it until it is snug into the socket to avoid any burnout or hazard at your home. It might be the case that the bulb you are using is not compatible with the socket or a switch as technology is increasing and has new inventions every day. In this case, it might be possible that the socket, bulb, or switch you are using is not compatible with one another.

3. Hazards or Burnout: In either of the cases, it leads to several hazards or Burnout. So, one should always check the compatibility of these devices. Once a check is done, then you should install it. It will help you avoid Burnout at your place. Sometimes Bulbs, sockets, and switches go well. But there are issues with the internal wiring mechanism. Sometimes the internal wiring system is loose. In this case, also Burnout may happen.

4. Voltage Imbalance: Thus, intermittent voltage causes the bulb to burn out faster than the actual life of that bulb. It is advised in this situation to call an electrical technician. He will resolve the issue. Variable Vibrations in voltage may cause the filament to break. Various heavy voltage-consuming electronic appliances at your home cause vibrations.

5. Various Appliances: The appliances are a washing machine, LED TVs, refrigerators, oven, and AC. Such appliances sometimes cause vibration in voltages. This variable voltage causes the breaking of filaments of the bulb. To resolve this issue, one should switch to LED-based lights that do not have a filament. Voltage can be very high sometimes! It is observed that 120-volt voltage is standard for electrical outlets. You can get some good remote controlled outlets under Your budget.

So, before installing a bulb, one should check that the bulb is not connected to a 220-volt outlet. Even if the bulb is put into a 220-volt outlet, it will shine brighter. But it causes the bulb to burn out very fast. Installing the right kind of bulb is also important. Let’s take an example that you have a  bulb that is operatable at 60-watt in a satisfactory manner. You can avoid all The issues by using a good bulb changer to change various bulbs.

But you wish to supply 120-watt. Thus heat increases in the bulb. Due to that, The life of the bulb reduces. So, one should use the bulb and wiring carrying the exact wattages. The life of the bulb reduces. So, one should use the bulb and wiring carrying the exact wattages. Moreover, you can install a good dust-to-dawn bulb to save power.

How To Change Emergency Light Bulbs To Retrofit LED Lights?

The steps to change the emergency light bulbs to retrofit LED lights are as follows.

1. First, choose the appropriate LED Light, which you are willing to install. 
2. After that, you should connect the blue wire to the blue wire of the housing and the red wire to the red wire of the housing.
3. Now, you should check for the batteries. They should be properly aligned and placed.
4. Now after the connection is done, check for the light is on or not.
5. Now you should check for the light by removing the plastic cover of it. Make sure to turn the power to OFF and wear gloves while working on the changing of the light.

Moreover, you can use a good high-brightness security light for your commercial buildings to be safe most of the time.

How Frequently do Bulbs Fuse?

As per guidelines, emergency lights should be maintained after regular intervals. The interval can be on a monthly and annual basis. At the very first, a 90-minutes emergency check is done. If the check fails, then replacement of the bulb becomes necessary. On average, An emergency light can stay on for  90 minutes up to 3 hours after the power loss.

When electricity is recovered, the bulbs will then refresh themselves. After that, these bulbs will start the function again. For continuous charging of the internal batteries of bulbs, one mechanism is used. For this, they are connected to the power source of the building. It is used as a power backup in case of power failure. According to the situation, various emergency lights are used, like exit plan lights and retrofit LED fit lights. There should be LED exit lights in your commercial buildings.

Some examples are Escape route lightning, High-risk area lighting, and standby lighting.

Reasons Of Failure 

a. Check on the main bulbs – Exit bulbs should be maintained regularly. This suggests they remain the entire time. If most bulbs are flickering or aren’t well lit, it would be time to alter them.

b. Low voltage bulbs – These are the bulbs that get on in an emergency. Suppose these bulbs aren’t functioning well. It may cause emergency lights to fail in a very breakdown.

c. Check on the battery – Sometimes, Bulbs work fine, but there is a battery issue. We must drop this possibility first before moving on to other solutions. 

FAQs

Can You Avoid Burned Out Emergency Exit Lights?

To avoid this, we should go ahead and install a Fire protection specialist kit within a specific time interval and maintenance. You should replace the emergency light bulbs and batteries at regular intervals of time to avoid any kind of burned-out.

Why Did Your Emergency Exit Light Burn Out?

There can be the failure of any of the three-component that will lead to burnout of emergency light.

The components are the Main bulb, low-voltage bulb, and the reserve battery.

The main bulb may be burned out which will lead to the ultimate failure of the light. If power is on and other lights are working well then you can conclude that the main bulb is burned out.

The low-voltage bulb will enlighten when there is no power and the light is working on the backup. If all of the lights are off and the emergency light is still on then it is working on backup. If your emergency lights are off, then there is low voltage emergency light is burned out. You should check with the batteries first then you can conclude that there is an issue with the backup services of the bulb.

If batteries are dead then you should directly replace the batteries. You should always get a good battery powered amber light bar for your emergency vehicles.

Final Talk

 An emergency can come at any time. So one should be prepared to deal with it. One should be ready to deal with an emergency. Such Incidents can be avoided by taking necessary measures. We should be well equipped with devices in such an emergency. Ensure that you have a full-fledged 72-hour kit with all the supplies.

If a longer lifespan and energy consumption are your priority, install an emergency light. Altogether, once invested in emergency light will help you in the long term.