How To Apply Non-Adhesive Window Film?

In any case, the sticky adhesive can cause harm to the window and make the sticky rolls of the film challenging to put on a smooth surface. Static cling window film is a non-adhesive vinyl material that is applied straight to the glass. As it is non-adhesive, this window film is exceptionally simple to apply and detach, making it perfect for transitory security necessities or leased properties. Here, you can follow the simple steps to apply non-adhesive window film. Yet, whenever needed, it will remain on the glass for a long time.

Steps To Apply Non-Adhesive Window Film

Quick Navigation

To start with, we will need to prepare our windows before applying the non-adhesive window film. Clean the outer layer of the window well with a cleanser and water to eliminate dust and other scraps that can hamper the clinging power of the film.

After we dry the window surface, we need to put glass cleaners on a perfect cloth and give it a last wipe down to guarantee that we have taken out every piece. We can also use a razor blade to scrape off any dirt left behind.

At last, run a wiper down the outer layer of the window to eliminate any fine residue. If properly done, we can enjoy a window with a cling film on top for quite a long time.

Step-1 : Cut The Window Film

We cut the window film and measure it so it’s a bit bigger than the window’s surface on each side. Utilize a straight edge to guarantee that the cuts are straight, particularly assuming that the film has an enhancing design. A dull edge can tear the film and a window film can dull the cutting edge of a utility blade. Thus, we should change to another cutting edge each time 8-10 feet of window film is cut.

Step-2 : Wet The Window

A liberal amount of cleaning solution should be sprayed all over the whole surface of the window. We need to ensure that there are no dry spots. We can also spray more solution first before applying the film if the solution starts to dry up. With this, we set the foundation intact before applying the window film.

Step-3 : Remove The Lease Liner

Eliminating the liner from the backside, side facing the window, can be difficult as well as interesting. We can take the help of a friend or a neighbor to hold the film for us or spread it out on a level surface. Here, we have to be mindful and make sure to not fold the liner.

We should wet our fingertips with the required solution to try not to leave any fingerprints on the film. Then by using our fingernail at one of the ends, we start dividing the liner from the film. As we start pulling the liner away from the film at an inclining point, we need to sprinkle a large amount of the cleaning solution on the non-adhesive side.

Try not to permit the film to move back upon itself. Lastly, it’s not important to spray the side facing the window, as long as the outer layer of the window is completely wet.

Step-4 : Place The Film

We need to guarantee that the sides of the window film and the window’s surface is completely wet with a cleaning solution as this permits you to move the film around and position it set up before it starts to adhere to the window.

Holding the film at its ends, we should press the wet side of the film to the window, beginning at the top and streamlining it as we go down. We then position the film so there is an equivalent measure of overlap on every one of the four sides.

Step-5 : Spray And Wipe

Now we grease up the external surface of the window film that is facing us by showering a liberal measure of cleaning solution over the whole surface. Beginning in the middle, we utilize the wiper and firm force to slide air pockets and an overabundance solution for the edges of the window film.

Redo the cycle every which way, eliminating as much air and dampness as possible. If the wiper begins to drag, we can shower on more solutions for the same. Wipe away the dampness along the edges with towels.

Step-6 : Trim To Size And Wipe Again

Now, a utility knife and a ruler can be used to trim the excess window film around each side of the window. We leave about 1/16-inch line of uncovered glass on each side to take into account the warm development of the glass and to wipe out any excess dampness.

As we manage to trim every one of the sides, we then shower the film down again with a cleaning solution and wipe out the excess solution utilizing extremely firm force. Lastly, wipe away the excess solution along the edges with towels.

Tools:

A Measuring Tape
A Utility Knife (with an extra number of blades)
A Wiper (or a squeegee)
A Window Cleaner
A Liquid Dishwashing Soap
A Spray Bottle
A Clean Rag

How Do You Make A Tint Solution?

Making a tint solution at home is one of the essential yet easy things to do. It can save us time, money and effort. We need a spray bottle and a few ingredients for the same.

We start with taking a generous amount of water along with either baby shampoo or any other gentle dish soap.
This helps to remove any dirt, oil or tar.
We can then add a few drops of alcohol to this mixture.
Alcohol being a drying agent, will help the water to evaporate fast.
Thus, leaving the surface clean and tidy.
Lastly, we need to mix the solution thoroughly and make sure the process is done properly.

With this, we need to put this mixture in a freshly prepared spray bottle and our tint solution is ready. Moreover, to cover your windows you can get a good motorized window blind under budget.

FAQ

1. Can I Use Water To Apply Window Film?

Yes, we can use water to apply window film but not hard tap water. It can stain the film and cause us some serious damage. The film aid provides pH balance and dryness clarity as well.

The cleanser solution acts as grease for the wiper during the process of cleaning the glass as well as film application. Using Gila Film Aid concentrate mixed with a liter of water is also highly recommended. Ammonia or vinegar-based products should be avoided at any cost to clean windows.

2. Why Does My Window Film Keep Falling Off?

One of the reasons for this can be improper application. Many customers feel that static cling window film is applied to the window with no other readiness like modest occasion enriching clings. This is off-base.

The window film should be applied to utilize a tint on arrangement ordinarily consisting of 3/4th water and 1/4th gentle dish cleanser. The cleanser makes the arrangement slicker, permitting it to be attached appropriately and for all air pockets to be pushed out during the wiping process.

This permits the barometrical strain and friction-based electricity to keep the static sling window stuck to the window. Another issue can be improper preparation of this.

It can be that there is an edge that stays lifted away from the window as the film was not managed as expected. Hence, at that point, it permits air to get behind the window film and causes it to gradually strip away which then, at that point, tumbles down.

Final Talk

The application of non-adhesive window film is therefore a process that needs time, effort and a little dedication as well. With the above-mentioned ways, we can apply the film on our way very carefully. It also saves us money and becomes pocket friendly. So, get the best window security film under your budget for your home. We can always call for professional help but it’s better to try and get to know how to do things ourselves rather than being dependent on someone.