Honeywell thermostat has to become an important part of people living in houses. It is essential as it helps in heating, and conditioning the temperature of your homes; hence, it comes in a box-like shape that helps show the temperature.
Therefore, just like other devices, it can also stop working for XYZ reasons, so it is essential to know how to fix it. Go through this guide to learn how to fix the Honeywell thermostat not working.
Honeywell Thermostat Troubleshooting Guide
Quick Navigation
Is your Honeywell thermostat not working too? Don’t worry, as we have got solutions for you. Go through the guide to learn how to fix Honeywell Thermostat.
1. Fix the Display if it is Blank
If you find out that the device is not working, then the first step that you should do is fix the display that has gone black on your Honeywell Thermostat.
It is regarded as one of the essential troubleshooting steps that can be performed easily if you follow the steps thoroughly.
A blank display on your device can happen in two situations: either the batteries are dead, or your HVAC system is not entirely closed. Check what is the case with your device and then do the steps accordingly.
2. Check HVAC Unit that Won’t Work
There can be another issue with your Honeywell Thermostat: if the device is in cool mode but passing the heated air or vice versa.
This can be another case where the system does not respond to the buttons or settings you are trying to hold onto the device. Do not panic if it does not work properly, as the fault lasts only a few minutes and can work properly.
Close all the doors and cabinets of your room where the device is installed, then set the temperature higher than your room temperature. If these steps do not work, then reset the circuit breaker.
3. Fix “Cool On” or “Heat On” is Blinking
Make sure to check if the device is turned on or not. Turn it on if it is not, as it will help you gain an accurate temperature. If it shows both temperatures simultaneously, do not worry, as the system can be delayed for 5 minutes.
These devices come with an inbuilt technology called a compressor protection timer that helps prevent short circuits if the power gets delayed or comes back after it is turned off.
4. Replace the Batteries
If the system is not working properly, the first step you can perform is to change the batteries. Most of the time, it can lead to resetting the system to its initial state and easily discarding issues created by software or viruses.
To change the batteries, make sure you follow the steps given below;
- Remove all the wires connected to the system and place them accordingly, so they don’t get combined.
- Take off the system from the wall and remove the batteries from it
- Stay for five minutes and then change the batteries
- Reconnect the wires with the system and turn them on
5. Examine Power Disruptions
This issue has been faced by a lot of people who own this system. There are a lot of complaints about the connectivity issues consumers of this device are going through; hence, if it is not working properly, make sure to check the wires for any breakages.
These steps can help you detect the problem your system is going through. Go through the steps, and fix the issues accordingly. You can also get professional help if you think performing the steps will be time-consuming.
Not Working With Google Home:
Follow the steps given below if the Honeywell thermostat is not working with google home;
- Try reconnecting the system.
- There are times when the system does not work with google home. There is a possibility that it can connect with the system and start to work as it was working before. To make it work again, reconnect the Honeywell thermostat with google home again.
- Contact Google Support
- Suppose the device does not work even after reconnecting the system. In that case, the best way is to contact google support and let them know your problems with the device, as they will have an appropriate resolution for your problem.
Not Working After Power Outage:
Here are the following steps that can fix your Honeywell Thermostat after a power outage:
Step 1: By resetting the Honeywell Thermostat
If a Honeywell thermostat is not working after a power outage, the first and most crucial step is to reset the device, as it can lead to the device start working again. This method is known to be as most essential if the device stops working after a power outage.
To reset the device, you must turn the device from its back and turn it off after a minute. It will start working after performing this step.
Step 2: Review the power of your system
The second thing you will need to inspect is whether the Honeywell thermostat is gaining power or not. It can happen if the system has dried batteries and insufficient power sources.
When batteries are dried, you can replace batteries by getting new ones from the stores near your house. And if the power source is not working, then check it.
Step 3: Get professional help.
If any steps are not working even after performing them properly, then you have only one option: contacting professional help.
Update them with your system’s problems, and they will help you. Getting support will not only solve the problem but will also save you time.
Not Working After Changing Batteries:
If you have changed the batteries and the Honeywell thermostat is still not working, try to see if you have used the correct batteries and if they are properly installed.
Step 1: Check the Batteries
The first and most crucial step is to ensure whether the batteries are correctly placed or not because a lot of consumers end up putting the wrong batteries in their system, and due to that, it does not turn on. To get accurate batteries, check the backside compartment of your device and note the voltage to get suitable batteries for your system.
Step 2: Substitute the batteries
After you get the correct voltage battery for your device, try to change them all in one go, as there are a few chances that they do not work well if you change them one by one. Also, keep in check that you do not end up mixing the old batteries with the new ones.
Not Working For Heat:
Is your Honeywell Thermostat not working for heat too? Do not worry, as we have got a few steps for you that you can follow to fix it.
The system can not function properly due to low batteries, power outage, temperature sensor not working properly, and more.
Reset the system
The first essential step to make your device work properly is to reset your system but before starting the process, follow these steps!
- Switch off the Honeywell thermostat and the circuit breaker
- Turn it backside and take off the cover from the thermostat and empty all the batteries that are placed inside of the system;
- Wait for a minute or two, and then place the batteries again in a proper way;
- And then switch on both devices.
Not Working On Auto:
Step 1: Inspect the wires
The first and most appropriate step you can do on your own is to check the wires if they are proper or not. Any cut or damage in the cables can lead to the device not working on Auto mode. The broken wire can also lead to short circuits, so check them correctly.
Step 2: Get Professional help.
The best way to check your device is by contacting the support team from where you got the system, or you can also get some professional help who knows this system. It will not be time-consuming for you, and the device can get repaired quickly.
Not Working With Alexa:
To fix the Honeywell thermostat that is not working with Alexa, follow the steps given below;
Step 1: Reset the Alexa
The first and easiest way is to reset the device. To do so, take the plug off your Alexa’s switchboard, wait for a few minutes and then put the plug back in its place; this can ensure your device is working properly.
Step 2: Check the Software and updates.
Most of the time, consumers forget to update the Alexa app, which is why it does not work properly. It is essential to check if there is any update coming or not. Make sure you update the app and software in check.
Not Working At Night:
The best way to fix your thermostat not working at night is by changing the batteries or resetting the device. Both of the steps have been mentioned in the above topics; check them out and accurately perform them so that your device works fine. If the problem still persists you can replace it with a good smart thermostat for multiple zones under your budget.
Final Talk
These steps are essential for the consumers who have Honeywell Thermostats, and all the given steps can be performed independently. But still, if you think it is necessary to get professional help, do not even think twice as it would be the best option for you. Talking about the best options you should get the best thermostat for your Airbnb.
Leave a Reply