How To Break An Ignition Lock With A Screwdriver?

To break the ignition lock one has to unscrew the plastic trim. If it is being difficult to break it then you can follow the below-given step by step guide. We have tested the steps twice and got successful results.

How To Break?

You can break the ignition lock in just a few following steps. You need to get a screwdriver that is medium in size to your ignition lock. It should be a flat-end screwdriver with a plastic handle.

• Step 1: Look For Screw That Is Keeps Outer Plastic Intact. Around your ignition lock, there is always some plastic. This is intact for protection and covering the behind portion of your lock. There must be some screws which are holding it. They might be below or somewhere behind the cover. You have to try to discover them. Try to look for only the right ones that are holding the cover of the lock. As a vehicle, it has several numbers of nuts and screws.
• Step 2: Unwind Screws. Once you have found the right screws and you are fully sure about it. You can proceed to the next step which is unwinding them. You have to rotate the screwdriver to the left-hand side. Continue to withdraw the screw outside of the plastic cover. Keep the screw carefully so that you can reuse them for placing the plastic trim back.
• Step 3: Uncover The Plastic Cover/Trim. Carefully extract the plastic trim or cover by lifting it away. Now you can see the ignition lock of the vehicle completely. So now we can move on to the next step here. You can vacate all the lingering pieces from it.
• Step 4: Remove the Remaining Screws. There are not only these screws but there are many other screws. You have to work on other screws here too. For example, the ignition lock is capable of working with all the electric components of the vehicle. So you have to also take care of them here. Try looking for these remaining bolts and start unwinding them. You have to unlock these areas too of the vehicle.
• Step 5: Put The Screwdriver Into The Keyhole. Try to put the screwdriver into the keyhole slowly so that you can make it open. Lastly, you should look out for taking off the screws. That are holding the mechanical and electrical components of the ignition lock. You can identify the electric parts of the lock as containing tuffs of wires.

Can I Remove The Ignition Lock Without A Key?

Yes, you can remove the ignition lock without the keys. Ignition locks are an exceptionally important part of our vehicle systems. But many times we misplace the keys. In this type of situation, when you need to take out your ignition lock. It often becomes very frustrating. Without wasting much time let us see how you can remove the ignition lock without having keys.

Step 1:

There is a middle space in your ignition lock. You need to plug a hole into that space. Continue the process until it reaches the point where you set your keys.

Step 2:

Now use the screwdriver into that hole you just made. Take a paperclip to put into the smaller hole. Place it to the left side of the keyhole.

Step 3:

You can pull out the lock cylinder gently using the paper clip you initially inserted. First, bend your inserted screwdriver to the left side. By this, the ignition cylinder will be also swiveled to the left.

Now If you wish to place a new ignition cylinder. You can do this with the help of keys or screwdrivers. Just try the same by moving your new ignition cylinder to the right position.

Is It Possible To Bypass An Ignition Switch?

Bypassing an ignition switch is very difficult to deal with in today’s modern cars. I know many old movies had projections of some cool thieves stealing a car.

But trust me, if that was even possible, it was all in old models. Many cars have features that make it impossible to bypass an ignition switch. The answer to your question only varies with the different cars.

Still, here are some basic things you can still try. The strategies useful in many cars to bypass an ignition switch are as follows:

1. Uncover The Ignition Switch

There is a plastic covering behind your steering wheel. As we have already told you above. You need to remove it first. It may have several screws at different places. You need to find them.

2. Identify Wires

As you can see the switch and related wires. Start to identify them. You have to find the first one which is terminal 30 (+ 12 V from the battery at all times). The second is terminal 15. (+12 V from the battery routed through the ignition switch.) It powers the engine. The third that is of interest to us is terminal 50. Is the command for the starter.

3. Cut Them

You can use a knife to cut them. Cut it in the proximity of the key ignition switch. After that do not forget to remove the insulation from their ends.

4. Short Wires

Short the two wires (30 and 15). After that Short momentarily the third wire (terminal 50) to the other two. Do that until the engine starts and remove it afterwards.

Remember, these steps will still be useless in modern vehicles. This is because most of them have electronic chips in the keys. As long as the computer of the car does not read the correct chip on the key. It won’t let any gas into the cylinders.

Why You Need To Break the Ignition?

It is very important to be aware of the conditions of the ignition system that is provided in your system. Because our vehicle is a type of machine.

It is of which one part is related to another and they all work together. If any part of the vehicle does not function properly for a long time.

Then it somehow starts to drag down the other part of the vehicle with it. Therefore, you change or break the despaired ignition switch as soon as you can.

Sometimes even if your ignition is alright and functioning properly. You don’t have the means to operate it. It could be because you might have lost the keys. The problem can also arise due to immobilizer problems. It works on specific codes. If you forget or lose them it will cause cracked ignition.

In all kinds of adverse situations, you are only left with an option to break your ignition lock.

Symptoms Of Bad Ignition Switch

Many times our vehicle hints about the need to change ignition switches. As already said above it is important to remove a bad ignition switch. It should be done before it starts to affect other parts of your vehicle.

Here I bring you the same by which you can identify a bad ignition switch:

• You are not able to start your car by the instant you put and turn the keys. It always takes some or more time.
• Problem while injecting and withdrawing the keys and while turning it. If you face problems while inserting the keys. Also If the keys are not freely moveable as before in your lock. Then there are strong signs of the issue.
• Problems with other car accessories can also occur due to broken ignition switches. Music systems, radios, bunkers, and many come under-car accessories. You may face them lagging while turning them on. Sometimes they work and sometimes they don’t.
• Your vehicle has bad battery life. Bad ignition can also affect the battery life of your car. The situation you may often face due to it is engine stalling. Difficulties in restarting your vehicle and many more. It affects those that are dependent on electric supplies.

Is It Possible To Drill Out The Ignition?

It is possible to drill out the ignition of your vehicle. Remember it is a very critical process and if not done properly can damage its subtle components. If you are seriously considering drilling out your ignition then consider these strategies.

1. Select a drill relevant to the size of your ignition cylinder.
2. Put the hard drill bits for the purpose. This is important as the metal can cause extra damage to your vehicle.
3. Drill a small hole just to hold your drill into it. Do it very carefully while keeping the speed low.
4. Now you have to gain the maximum speed while drilling out your ignition cylinder. Please note that you should not push while drilling as it can result in unwanted harm.

Reasons For Ignition Lock-Off

If your keys are locked off in your ignition and are not turning. Reasons which affect this include normal wear and tear of your keys. Time may affect the efficiency of your ignition and keys.

It can also happen by any jagged and ragged experiences of the keys. Due to this, the lock does not line up suitably with the keys because of which your work is stuck-up.

In many vehicles, after vacating the keyhole if the steering wheel is jolted or banged. It results in the locking of the keyhole. The reason for this is to protect your vehicle from any theft.

Make sure the keyhole in your ignition switch is free of any obstruction. This may be the reason why your ignition is locked off.

FAQ

Can you drill out a lock cylinder?

Opening an ignition-lock cylinder is a job that is only done with its particular ignition key. Nonetheless, you can still drill your lock out in only a pinch. But this method should always be your last option. This is because you can damage delicate elements of your ignition lock cylinder. If your ignition lock and switch are separate parts, there is an even greater risk. You will end up destroying your ignition switch and the lock cylinder both.

Can you drill out a car lock?

Yes, you can certainly drill any car lock. You have to just make sure that the lock cylinder is made of weaker metal than that of the drill bit that you are going to use. This method can be applied to car doors and some older cars. Modern cars have a more complicated locking system. If your car door is a basic”means of egress” for fire security, it already does not require keys. As In many cars it will be an offense of fire code. You have to also remember by drilling a car lock one mistake can lead to replacing the whole cylinder. 

How do you open a locked ignition?

Maybe it would become hard for some car holders to open the ignition if they can keep trying to turn their car on. Luckily, by taking a few easy points you can shortly open it again.

Step 1

Assure that the vehicle’s transmission is in the park. If you keep manual transmission you can avoid this point and shift to Step 2.

Step 2

Push the brake of the car down with your foot on the right side. If the key to your car isn’t in the ignition, place it there now.

Grip the steering wheel firmly with your left hand and put your car’s key in the ignition with the help of your right hand. Rotate your steering wheel to the right side and then left when you are twisting the ignition key while you start the car. Joining in these 2 actions simultaneously will free the ignition button and will enable you to switch on your car.

Final talk

Situations in which you have only one option to wreck the ignition switch system may arise. This can be either due to wear and tear in the lock system or due to loss of keys. The process is simple. Steps only require a flat screwdriver, paper clips and drill. The solution provided above is to only prefer in situations you have no other options. As there are delicate components involved it is advised to have professional help.

You should remove a torn out ignition as soon as you find symptoms. Bad ignition affects other parts of your vehicle. Moreover, it may cause trouble in any unfavourable condition. Don’t forget to do service of your vehicle.